Póthaj rendelés +36 30 526 5672

How to do extensions? Step-by-step guidance

by Peter Juhasz on November 18, 2019

The hair extensions are tinkled to accommodate the hair in a larger unit.

Ideally, the hair extender expert would combine the hair (one strand of hair to one strand), thus avoiding a 2-3-month lay-up and tangling process. As the appropriate technology has not yet been developed, the hair extender needs to be tinkered before it is fitted to its own hair.

For heat fitting and ring-forming, it is also necessary to cover the base of the extensions with a thermosetting adhesive.

The average hair contains approximately 0,5-1 grams of hair depending on the length of the hair.

For rings and vaginal extensions cylindrical hairsWe make them.

cylindrical hairs

The cylindrical locks are handmade as follows:

  1. Remove approximately one cm of hair extensions from the tress line and then flick the hair remaining from the beard section
  2. (instead of stroking out of an armrest, pull out often less hair)
  3. read me 2-3 piecesCrystalline keratinTake it up to the stem of the hair extensions
  4. As long as the glue is soft (warm) between your thumb and your index or middle finger, roll it until it is in perfect shape
  5. Cut the sharp end so it doesn't sting the scalp after it's been applied

Important! You have to separate so much of the hair that the prepared portion fits well into the microring. If the extensions get tight, it's no good, because you won't fit your own hair next to it. You'd better make smaller bangs and increase their size if you don't think they're big enough.

Micro ring

M Flat hair they serve a different purpose than cylindrical ones. Actually, cylindrical hair can be used for heat fitting, but it's much harder to melt. Therefore, the Hot-fitting hair extensions it is preferable to produce easily meltable, flat hair.

The production of flat (U tip or Flat tip) hair is different from making cylindrical hair. It needs more adhesive material and a smooth surface on which to apply soft (hot) hair.

(some people make flat hair with pliers, we don't work that way, but we'll make a short video of it)

  1. Remove approximately one to five cm of hair extensions from the tress line and then flick the hair remaining from the beard section
  2. (instead of stroking out of an armrest, pull out often less hair)
  3. read me a 4-5 pieceCrystalline keratinTake it up to the stem of the hair extensions
  4. While the glue is soft (hot), lift it over the table top and apply one finger to the soft, sticky part of the stopper. (Be careful because the glue may still be hot, wait until it gets a little cold)
  5. Carefully try to shape the sides so that they don't have a "duck leg" shape, the sides have a parallel plane.
  6. Leave it on the table and keep making the hair and glue it together.
  7. When a good amount of hair is collected (you can't get to the table), grab a pair of scissors and pull the hair out of the table with a firm movement and cut it nice and straight at the end (leave around 0,5-0,8 cm of the adhesive part)

Oh, my God!

Click here to find a short video of making flat hair.

Click here to see how to use the keyboard for tinkering

Important! If you make too much hair, the hair extender will do the job faster, but the customer's own hair may be pulled out from excessive stress. Don't make hair bigger than one gram. The easy way to verify that is to measure hair on a kitchen floor after making a 20-30-inch hair.

Manufacture of braids for heat fitting

Hair extensions aren't easy to learn, but after a few hundred hairs, they're more routine, after a few thousand, you'll be quite good and quick.

It's important that the hair quality is always perfect, because then someone else will be working with it.

On the other hand, let's honor the man with a nice job who's been growing his hair for years so that someone can use it to extend his own.

Work waste-free.

Cut the hair from the stress line all the way from the stress point, if you leave half an centimeter of hair on it, it's 15-20 percent weight loss.

I wish you good luck with your hair. I hope I could help.

We'll be making video footage soon, which I will also attach to this educational material.

LEAVE A COMMENT

Please note, comments must be approved before they are published


BACK TO TOP